Home Products About Us Contact Us

OVERVIEW
The CP93 is an electronic controller designed to operate access automation systems (e.g. swing gates, sliding gates, roller shutter door operators etc.) that incorporate either a single or double single phase, reversible AC induction motor. The controller has various pre-configured inputs and outputs in order to operate these types of systems in addition to many programmable features.

The user interface is enhanced using a three character digital display. Combined with two pushbuttons to navigate through the programming menu and a further pushbutton to select the required function, the programming of the controller to suit a multitude of requirements is very quick and easy. The board is fitted with diagnostic LED's for easier fault finding and installation.

The controller uses either limit switch inputs or a timer system to suit the end of travel limits for the particular installation.

In order to prolong the life of the motor switching relays, the controller incorporates zero crossing switching. This includes the ability to adjust the cross over point until minimum arcing of the relay contacts occur.

It is the all in one solution for new AC gate motors systems.

It is also the ideal replacement for an existing system where there is either no longer support or service available for the controller, or the controller has been damaged beyond repair by lightning or electrical surges.

FEATURES
GENERAL FEATURES
Incorporates protection against lightning and high voltage surges. Three digit, seven segment LED display with three buttons for programming features. Status of each feature programmed can be easily determined via display. On board TEST button to activate standard trigger input. Easily removable connectors.

OPTIONAL INPUTS

Standard trigger input with the following selectable parameters:
	— Repeated triggers start, stop and reverse motor(s).	STANDARD
	— Repeated triggers start and reverse motor(s)	REVERSING
	— Operate in open direction only with automatic closing after preset auto close time. Auto close time is programmable.	CONDOMINIUM
	— Auto reverse on clearing standard closing protection input.	PIRAC MODE
Trigger input to operate motor(s) in opening direction only. Using combination of standard and free exit inputs:		FREE EXIT
	— Separate operation of motor(s) in each direction with emergency stop as separate input to stop motor(s)	PLC MODE
	— Constant activation of input to operate motors with separate operation in either direction.	DEADMAN CONTROL
Partial cycle opening of master motor for programmed time with automatic closing. Automatic close time adjustable.		PEDESTRIAN OPENING
Independent limit input for both motors in both directions configurable for NO* or NC* contacts		LIMIT SWITCH INPUT
SAFETY INPUTS
Safety device input programmed to stop and reverse motor(s) when closing in one direction. Input configurable for NO* or NC* contacts		STANDARD CLOSING BEAM OR INDUCTIVE LOOP INPUT
Safety device input programmed to stop and reverse motor(s) when opening. Input configurable for NO* or NC* contacts.		OPENING BEAM OR INDUCTIVE LOOP INPUT
Emergency stop input that will cut power to motors during operating cycle regardless of operating mode.		E-STOP
ANCILLARY FUNCTION INPUTS
Independent control of pillar light relay.		PILLAR LIGHT CONTROL
	— Activate for preset timer period. — Activate to switch ON or OFF.
ANCILLARY OUTPUTS 12V DC output to power ancillary components. (e.g. Radio receivers, infra red beams etc.)		ANCILLARY 12V DC
12V DC output to power ancillary components. (e.g. Radio receivers, infra red beams etc.)
Status indicator provides remote and local indication of gate status		STATUS LED
Gate operating direction (opening/closing) Gate end of travel position (open/closed)
Potential free contact closes for a programmed period.		PILLAR LIGHT TIMER
Potential free contact closes for programmed period on start up of MASTER motor in opening direction only. NO* or NC* contacts selectable.		SOLENOID/ MAGNETIC LOCK RELAY

NOTES:
* NO= Normally Open, NC= Normally Closed
For application requiring >3 Status LED'S use multi LED driver interface (ref. CP78).

DIMENSIONS
Mounting hole set A - 112.5mm X 103.5mm between Ø4.5mm hole centres.
Mounting hole set B - 156.5mm X 135mm between Ø4mm hole centres.
Maximum height - 43mm.

SPECIFICATIONS
INPUTS

1. AC supply to controller 220V AC single phase.
2. Power consumption in standby mode 1.8 Watts.
3. Input contact requirements: NO*/NC* Potential Free switching to common.

OUTPUTS

1. Motor channels - Two at 220V, 5A (fused).
2. Timed potential free output (courtesy light contact). Potential Free NO* contact; Max. 3A (100W) (fused).
3. Timed potential free output (solenoid lock). Potential free; Max 3A @ 12V or 10A @ 24V. Selectable NO* or NC* contacts.
4. Status indicator 5V current limited signal for remote LED (Max 3 LED'S in parallel).
5. Auxiliary DC supply 12V, max 300mA (fused).

TIMERS

1. Motor run timer: adjustable 1 - 255 seconds in 1 second increments.
2. Auto close timer: adjustable 1 - 255 seconds in 1 second increments.
3. Auto close override timer: adjustable 1 - 255 seconds in 1 second increments.
4. Direction reversal delay: adjustable 100ms to 25.5ms in 100ms increments.
5. Timed potential free contact (pillar light relay): adjustable 10 - 2550 seconds in 10 second increments.
6. Timed potential free contact (solenoid lock): adjustable 1 - 255 seconds in 1 second increments.

ENVIRONMENTAL

1. Operating temperatures: -50 to + 55°C.
2. Operating humidity 20 - 80% (no condensation).