Traffic Barriers

SECTOR

SECTOR - HIGH-VOLUME INDUSTRIAL TRAFFIC BARRIERS

SECTOR - HIGH-VOLUME INDUSTRIAL TRAFFIC BARRIERS
SECTOR - HIGH-VOLUME INDUSTRIAL TRAFFIC BARRIERS #2
SECTOR - HIGH-VOLUME INDUSTRIAL TRAFFIC BARRIERS #3

Lots of vehicles coming in and out? You need something that goes up and down. Fast!

The SECTOR high-volume industrial traffic barrier gives you the ultimate in traffic control. Powered by a beefy custom-built DC motor and gearbox, the CENTURION SECTOR can raise up to a three metre boom pole at a blistering 1.2. seconds.

Operating slightly slower, the SECTOR will effortlessly raise up to a six metre pole smoothly and reliably.

The SECTOR lives fast, but it most certainly doesn't die young. Designed for tough, high-volume traffic control, it will work all day, it will work all night - lasting millions of cycles.

Add full battery backup, and the SECTOR is always at your service

Document Downloads


CENTINEL

CENTINEL - MANUAL TRAFFIC BARRIER

CENTINEL - MANUAL TRAFFIC BARRIER
CENTINEL - MANUAL TRAFFIC BARRIER #2
CENTINEL - MANUAL TRAFFIC BARRIER #3
CENTINEL - MANUAL TRAFFIC BARRIER #4

If the requirement is to cordon off a parking lot or entrance to a housing estate where a manned guard is always present, then the CENTINEL manual traffic barrier is a perfect cost-effective answer.

The CENTINEL is available with 3, 4.5 and 6 metre boom pole lengths. Using an internal spring the CENTINEL avoids the use of unsightly weights to counterbalance the boom pole. This results in a particularly compact and aesthetically pleasing barrier befitting the entrance to any up-market installation.

When we designed the CENTINEL manual traffic barrier, we had the user in mind. After all, just because it's a manual traffic barrier doesn't mean that you have to do all of the work!

Document Downloads


CENTOR

Centor Traffic Barrier - A traffic barrier designed for tough high volume operation

Centor Traffic Barrier - A traffic barrier designed for tough high volume operation

The CENTOR traffic barrier is the right product for high volume access control applications such as shopping mall parking lots, large business estates etc.

It incorporates a 220V torque motor. The unique operating characteristic of this motor provides the system with a continuous rating (100% duty). It is very efficient with a barrier raise time of less than 3 seconds (3 & 4.5m boom pole models).

It offers fail safe operation in that the barrier will automatically raise in the event of a mains power failure. The CENTOR barrier enclosures are robustly constructed from either mild or stainless steel (Typically grade 430) to provide a tough and long lasting product.

The reliability of the system is further enhanced, by the simplicity of the design and the minimal quantity of mechanical components used.

It uses the CENTURION CP91 controller which offers proven reliability and the flexibility that it can be programmed to suit majority of applications.

The unit is very easy to install as it requires only two sturdy rawl bolts into a proper foundation to secure it in position.

Operation

The torque motor used in the CENTOR barrier is a high impedance motor that is designed to run continuously. It therefore provides an operating duty of 100%. It does not use any limit switches to power off the motor in the barrier raised or lowered positions. The CP91 controller controls the direction of the motor to either raise or lower the boom. At the end of each cycle the motor linkage is driven up against a rubber stopper and is held there by the continuous operation of the motor, until the next raise/lower signal.

The unit is fitted with an internal spring counterbalance to assist the motor when raising the boom pole. In the event of a mains power failure the counterbalance springs will raise the boom pole automatically. The CENTOR units for either a 3 or 4.5m boom pole, use the same torque motor, it is only the spring counterbalance that varies. The 6m unit uses a motor with a higher torque rating and counterbalance springs.

Automatic vs. Semi Automatic Operation

We offer the CENTOR barrier configured for either automatic or semi-automatic operation.

  • Semi-automatic operation - Standard entry/exit control via remote, keypad, pushbutton etc. Auto-close is available to lower the boom. Any infra red beam or inductive loop input is for protection purposes only i.e. prevent from closing onto a vehicle.
  • Automatic operation - This mode is to allow interface to a ticket vending machine, card reader etc. The system is tied in with an inductive loop to automatically lower the boom when the vehicle has passed. If a mains failure occurs the barrier will automatically raise the boom.

The unit is supplied fully wired with relay bases for both the closing/safety loops and free exit loop detectors. NB: The loop detector modules are supplied as optional extras.